quality Diesel Forklift Truck & 4 Wheel Electric Forklift manufacturer

The forklift has changed from the previous fuel to the current electric forklift, which brings many conveniences to our lives. Some drivers find that after long-term driving, electric forklifts will make noise after a period of time. How is the noise of the forklift generated? What precautions should be taken to operate the clutch to avoid noise? The following is a detailed introduction for everyone. a. Reasons for noise problems of electric forklifts 1. Check whether the conflict between the guide wheel, the roller and the mast is too large. Whether the cooperation gap between the fork and the fork frame crossbeam is too large, these factors will cause the electric forklift to produce greater noise during use. 2. The gap between the chain and the pin of the chain pin is too large, or the gap between the upper and lower staples of the fork and the crossbeam of the fork frame is too large. 3. Loose fasteners, severe wear of the guide wheels and rollers of the car body, resulting in a large gap. b. Matters needing attention 1. When the electric forklift is not using the clutch, do not put your feet on the clutch pedal to avoid the semi-linkage phenomenon of the clutch, affect the power transmission, and aggravate the wear of clutch plates, clutch bearings and other mechanical parts. 2. No matter whether it is high-end downshifting or low-range upshifting during driving, it is forbidden to shift the clutch without collapsing. 3. Frequently check and maintain the clearance between the separation lever and the separation bearing, and check and lubricate the clutch separation bearing, seat and sleeve on time. There are many reasons for the noise caused by electric forklifts. The staff should drive the forklift to the parking lot facility for special investigation and find the reason, so as to solve the doubt of the forklift noise from the source. The staff should pay attention to the operation and try to avoid it Noise generation.

The unmanned forklift has the advantages of accurate positioning, no infrastructure, independent programming, and flexible operation. Its navigation uses remote control technology, which not only saves labor, but also effectively prevents the occurrence of dangerous accidents. Currently, the two mainstream navigation methods are based on SLAM environment natural navigation and reflector navigation. 1. Reflecting plate navigation principle: Reflecting plates are arranged at a certain distance around the driving route of the forklift. The laser scanner on the forklift emits laser beams. These laser beams can quickly collect the laser beams reflected by the reflecting plate. Based on the data of multiple laser beams reflected back, the current position and course of the forklift in the environment can be determined, and in conjunction with the motion controller control algorithm, the forklift can be driven automatically. 2. Natural navigation based on the SLAM environment: SLAM is simultaneous positioning and mapping. In an unknown environment, the robot positions itself through the internal sensors and external sensors carried by itself, and on the basis of positioning, uses external sensors to obtain Environmental information, incrementally build an environmental map.

Electric forklifts mainly carry cargo in a fixed space, so how to drive an electric forklift? What is the specific method of use? Let's listen to the introduction of electric forklift manufacturers. Instructions for use of electric forklifts: 1. Depress the clutch pedal, start the engine, gradually refuel to raise the temperature of the engine, properly operate the multi-way valve, and lift the fork off the ground by about 15-20CM. 2. Switch to low gear, choose forward or backward gear, gently lift the clutch, slowly increase the throttle, and the forklift starts. 3. Alignment. Go to the pick-up place, slow down the speed, adjust the height and level of the fork, lightly step on the clutch, semi-linked. Adjust the direction until all forks fork into the goods, refuel to lift the forks, 15-20CM away from the ground. 4. When moving the forklift, the speed should be slow, the truck should be stable, and brakes should be used less. 5. Delivery. When the forklift arrives at the place where the goods are placed, slow down the vehicle and move the joystick gently. After the goods are stabilized, the forks can be emptied before returning. The above is the specific method of opening the forklift. In addition, in the process of use, it should be flexibly operated according to the actual situation. Before operating, be sure to understand the operation manual of the forklift and understand some common faults.